1. F00ZC01310 CRDI Injector Valve Set Replacement Conditions
Under the microscope, magnify 20 times to check that the oil inlet hole of the valve cap and the oil return hole of the bonnet are not worn, grooved, scratched, damaged, rusted or dented.
| No. |
1 |
2 |
3 |
| Image |
 |
 |
 |
| Description |
CRDI injector valve set oil inlet hole location |
CRDI injector valve set oil return hole location |
The oil inlet and oil return holes of the CRDI injector valve set are free of wear, grooves, scratches, damage, rust, dents, which do not need to be replaced |
| No. |
4 |
5 |
6 |
| Image |
 |
 |
 |
| Description |
The CRDI injector valve set oil hole is recessed and needs to be replaced |
The CRDI injector valve set oil hole is worn and needs to be replaced |
The CRDI injector valve set oil hole is punched and needs to be replaced |
- The wear of the top oil return hole causes the oil return to be too large and the leaking injector cannot inject oil.
- The oil inlet hole on the side is blocked,causing the injector to fail to establish the pressure chamber and the injector cannot work normally
- Wear of the oil chamber of the valve cap will cause fuel injector failure. In severe cases, the fuel injector will not work properly.
Magnify 20 times under a microscope to check whether the valve stem is worn, the surface is not smooth, discolored, or rusty.
| No. |
1 |
2 |
3 |
| Image |
 |
 |
 |
| Description |
The valve stem is worn out and needs to be replaced |
The valve stem surface is not smooth and colorless, and it needs to be replaced |
The valve stem is rusty and needs to be replaced |
2. F00ZC01310 CRDI Injector Valve Set Storage Standard
- Choose a Suitable Storage Place
The warehouse and cargo yard where the CRDI injector valve set is stored should be kept clean and dry, and away from the factory buildings that generate harmful gases and dust; do not mix with acid, alkali, salt and other substances; the storage place should have a good drainage system; the cargo yard should be flattened with gravel or furnace ash etc. to enhance the water permeability of the surface layer to keep the reservoir area dry.
- Strict Requirements of Warehousing
Strict inspections should be carried out when the CRDI injector valve sets are put into storage, the surface cleaning work should be done well to remove water traces, oil stains, ash and other dirt, remove the rust and do anti-rust treatment in time. Packaged CRDI injector valve set must be protected from damage.
- Keep The Warehouse Dry And Preventing Moisture
The relative humidity is usually below 70% for the CRDI injector valve set placed in the room, and the corrosion of the CRDI injector valve set is significantly reduced.
CRDI injector valve set must be stored in the warehouse, and they are forbidden to store in the same warehouse with commodities with high water content.
After the CRDI injector valve set is exposed to rain, the corrosion rate will increase significantly. The purpose of sealing is to isolate the CRDI injector valve set from rainwater and humid air, so the warehouse window should be checked in time to avoid rainwater entering the warehouse.
If the CRDI injector valve set package is damaged, it should be repaired or replaced; when the package is damp, the packaging material should be dried; if the original anti-corrosion and oil applied at the factory is found to be damaged or dried up, it should be cleaned and re-applied oil in time.
It is forbidden to leave the CRDI injector valve set exposed in the air for a long time.
It is forbidden to store acid, alkali, salt and other substances together with the CRDI injector valve set.
The unpacked CRDI injector valve set must be rust-proof during secondary storage.
The material on this passage “F00ZC01310 CRDI Injector Valve Set Encyclopedia” is the property of www.crdiinjectorvalveset.com and is protected by international copyright laws. The content is allowed to be cited for non-profit purposes, and please indicate the source: “Reprinted from www.crdiinjectorvalveset.com” to respect the content supplier’s labor results. Copying, reproducing, redistributing, modifying, publishing, transmitting without permission is strictly prohibited. We reserve the right to pursue legal action against those who use the content illegally.
If you have any questions, please feel free to contact us at hison@shumatt.com.
